The free remote control flashes red: What to do?

Francis

You are a Free subscriber and you use a remote control to control your box . But then, one day, you notice that your remote control is flashing red quickly and is no longer working properly. What is the cause of this problem and how to fix it? This is what we will see in this article.

Possible causes of the Free remote control flashing red

There are several reasons why your Free remote is flashing red quickly . Here are the most common:

The remote control is discharged
The remote control is defective
The remote control is out of sync

Solutions to resolve the red flashing of the Free remote control

Solutions to resolve the fast red flashing of the Free remote control

If your Free remote is flashing red quickly, here are the solutions you can try to resolve the issue:

Change the batteries

The first thing to do is to check the battery status of your remote control. If they are worn out, replace them with new batteries of the same type ( LR03 or AAA ). If the problem persists, continue to the next solution.

Reset the remote

If changing the batteries isn't enough, you can try resetting your remote. To do this, you must simultaneously press the Free and Standby for 10 seconds, until the red LED goes out. Then release the buttons and short press the Free . The red LED should flash once then go out. If the problem persists, continue to the next solution.

Resynchronize the remote

If resetting the remote control isn't enough either, you can try resynchronizing your remote control with your box. To do this, you must follow the following steps:

Turn off your box by pressing the On/Off on the back.
Bring your remote control closer to your box (less than one meter).
Press the Free and Sleep for 10 seconds, until the red LED turns off.
Release the buttons and briefly press the Free . The red LED should flash once then go out.
Turn on your box by pressing the On/Off located on the back.
Wait for the box to display the time then briefly press the Free . The red LED should flash once then go out.
Your remote control is resynchronized with your box and should function normally.

FAQs

Here are some frequently asked questions from Free remote users:

How do I know if my Free remote control is discharged?

You can find out by pressing any button on your remote control. If the red LED flashes weakly or not at all, your batteries are discharged. If the red LED flashes normally, your batteries are still good.

How do I know if my Free remote control is defective?

You can find out by testing your remote with another compatible device, such as a TV or DVD player. If your remote control does not work with this device, it is defective. If it works, it is not defective.

How do I know if my Free remote control is out of sync?

You can find out by pressing the Free button on your remote control. If the red LED flashes quickly, your remote control is out of sync. If the red LED flashes normally, your remote control is synchronized.

How do I change the code of my Free remote control?

You can change the code of your Free remote control if you want to control several boxes with the same remote control or if you want to avoid interference with other remote controls. To do this, you must follow the following steps:

Turn off your box by pressing the On/Off on the back.
Press the Free and Sleep for 10 seconds, until the red LED turns off.
Release the buttons and briefly press the Free . The red LED should flash once then go out.
Press the number button corresponding to the code you want to assign to your remote control (1 to 9). The red diode must flash as many times as the number chosen then go out.
Turn on your box by pressing the On/Off located on the back.
Wait for the box to display the time then briefly press the Free . The red LED should flash once then go out.
Your remote control has changed code and must work with the corresponding box.

How do I repair my Free remote control if it is broken?

If your Free remote control is broken, for example if it no longer lights up or if a button no longer works, you can try to repair it yourself by following the advice in this tutorial: https://www.youtube.com /watch?v=Zw7Q6x2Zm0k. Otherwise, you can contact Free customer service to request a replacement or repair of your remote control.

How do I clean my Free remote control if it is dirty?

If your Free remote control is dirty, for example if it has fingerprints or dust, you can clean it by following these steps:

Remove the batteries from your remote control and set them aside.
Use a soft, slightly damp cloth to wipe the surface of your remote control. Do not use chemicals or abrasives that could damage your remote control.
Use a cotton swab or toothpick to clean the gaps between the buttons and around the red LED. Do not press too hard to avoid damaging the electrical contacts.
Let your remote air dry for a few minutes.
Replace the batteries in your remote control and check that it works properly.

How do I use my Free remote control with other devices?

You can use your Free remote control with other compatible devices, such as a TV, DVD player or amplifier. You can even use it to access the secret menu of your Samsung television .

To do this, you must program your remote control by following the following steps:

Turn on the device you want to control with your remote.
Press the TV on your remote control for 3 seconds, until the red LED lights up.
Press the number button corresponding to the type of device you want to control (1 for a TV, 2 for a DVD player, 3 for an amplifier).
Power button on your remote control until the device turns off.
Release the Power and short press the TV . The red LED should flash once then go out.
Your remote is programmed to control your chosen device. You can test other functions of your remote control by pressing the corresponding buttons.

How do I deprogram my Free remote control if I no longer want to control other devices?

You can deprogram your Free remote if you no longer want to control other devices with it. To do this, you must follow the following steps:

Press the TV on your remote control for 3 seconds, until the red LED lights up.
Press the number button corresponding to the type of device you want to deprogram (1 for a TV, 2 for a DVD player, 3 for an amplifier).
Free button on your remote control for 10 seconds until the red LED turns off.
Free button and briefly press the TV . The red LED should flash once then go out.
Your remote control is deprogrammed and no longer controls the chosen device. You can only control your box with your remote control.

Conclusion

Now you know why your Free remote is flashing red quickly and how to fix this problem . We hope that this article was useful to you and that you were able to regain control of your box. If you want to change your mobile and benefit from a state-of-the-art smartphone at an advantageous price, discover Free Flex, Free's rental with purchase option service . If you have any further questions or experience other difficulties with your Free remote control, please do not hesitate to contact Free customer service on 3244 or visit their website